A thin piece of material placed between two surfaces to obtain a proper fit, adjustment, or alignment. The piece can also be analyzed to measure furnace carbon potential (that is, because while in the furnace it will quickly carburize to a level equal to the furnace carbon potential).
1. n. a thin piece of material used to unlock the cylinder plug from the shell by separating the pin tumblers at the shear line, one at a time 2. v. to unlock a cylinder plug from its shell by using a shim
A short, thin piece of wood, usually oak or red cedar, used between two pieces of wood or between a piece of wood and steel, earth, or rock. The shim is used to bring a ledger, stringer, or tread to level.
A wedge (thicker at the toe).
A thin metal plate or washer used to pack or pre-load a bearing.
A piece of metal or other material used to fill out a space.
a wood wedge used to secure and align a window or door in a rough opening
(1) A thin, often tapered piece of material such as metal or wood used to fill in space between things.(2) A round, usually magnetic disc used with a dado blade to provide a wider cut.
a thin wedge of material (wood or metal or stone) for driving into crevices
a piece of material added at a critical point to realign something
a thin piece of metal or composite used to fill in space between components, for adjustment of fit, in a mechanical assembly
a thin piece of metal that goes between your CPU's package and your heat transfer device (heatsink, waterblock etc
a thin sleeve of aluminium or thermoplastic, which is inserted between the seatpost and the frame, adjusting the seatpost
a thin, sometimes tapered, piece of mate- rial used to fill in space between things
a thin wedge of wood which can be purchased inexpensively in packets at your home center or made yourself from scraps of wood
a thin wedge that can be placed between two surfaces to tightly fill a gap, as between a door jamb and a cripple
A spacer (usually a wood wedge) placed between a frame and the wall structure to hold the frame in position.
Thin metallic or paper wedge used to center a shaft in a hosel. The use of shims is not a highly recommend practice among clubmakers.
A thin, often tapered piece of wood used to fill in space between things. SHRINKAGE - The reduction in dimension or volume which takes place in timber when the moisture content is reduced below fibre saturation point, expressed as a percentage of the original dimensions or volume. Linear shrinkage occurs in three directions: radial, tangential and longitudinal.
Wood to metal used to level or plumb.
A thin piece of material used between two surfaces to obtain a proper fit, adjustment, or alignment, or to level a machine.
Thin material inserted to make adjustments in level or plumb. Tapered wood shingles make excellent shims in carpentry work.
A piece of wood or metal used to fill in required clearance space for shutter installation.
A thin material, fiber or metallic spacer used to adjust the distance or angle of an item.
A piece of material used to fill in the space between two surfaces.
A thin strip or wedge of wood or other material used to fill a gap between two adjoining components or to help establish level or plumb. Home Improvement Encyclopedia
A thin piece of material (often tapered) used to fill in space between things (for support, leveling, or adjustment of fit)
a thin, often tapered piece of material used as a leveler or filler between such materials as wood, stone, and metal; the removable, interchangeable "spacers" used to achieve specific neck angles in Taylor new-tech neck joints are a form of shim.
A thin, often tapered, piece of material, such as metal, used to fill in space between things for support, adjustment, or leveling.
Thin tapered piece of wood used for leveling or tightening a stair or other building element.
A thin metal ring used to adjust (shorten) valve spring installed height. The shim is installed between the bottom of the valve spring and the spring seat on the cylinder head. Multiple shims of different thickness may be used to get just the right height. In this case, the thickest shim should be installed next to the spring.
A long, narrow repair of wood or suitable synthetic not more than 3/16 inch wide.
A small piece of scrap lumber or shingle, usually wedge shaped, which when forced behind a furring strip or framing member forces it into position; also used when installing doors and placed between the door jamb legs and 2 X 4 door trimmers; metal shims are wafer 1 1/2" X 2" sheet metal of various thickness' used to fill gaps in wood framing members, especially at bearing point locations
To level or plumb something by sticking a thin piece of wood or plastic underneath.
THIN TAPERED PIECE OF WOOD USED FOR LEVELING, TIGHTENING, OR PLUMBING STAIRS, DOORS, WINDOWS, AND OTHER STUFF.
Spacers of precise, predetermined thickness used between pads to establish a proper working relationship.
Thin tapered pieces of material such as a shingle. Used for leveling timbers.
A wedge shaped piece of wood used between objects to adjust or secure their position.
A thin piece of material used between parts of an assembly, to change and fix the distance between parts, when parts are fastened.
A thin piece of material used between two surfaces to obtain a proper fit, adjustment, or alignment. Shims are also thin metal sheets that are inserted between the die and press to align the binder surface of the die and alter binder pressure.
thin piece of material used to smooth, l evel, or finish area between two irregular surfaces.
Using a tapered wood strip, called a shim, to fill gaps so that structures are level and plumb by placing it between two members to fill in uneven areas.
In engineering, a shim is a thin and often tapered or wedged, piece of material, used to fill small gaps or spaces between objects. Shims are typically used in order to support, adjust for better fit, or provide a level surface. Shims may also be used as spacers to fill gaps between parts subject to wear.